{"id":2394,"date":"2016-04-23T12:21:22","date_gmt":"2016-04-23T10:21:22","guid":{"rendered":"http:\/\/hmg-maschinen.de\/wp\/?page_id=2394"},"modified":"2016-07-28T16:59:19","modified_gmt":"2016-07-28T14:59:19","slug":"fragen-zum-holzspalter","status":"publish","type":"page","link":"https:\/\/hmg-maschinen.de\/en\/service\/faq\/fragen-zum-holzspalter\/","title":{"rendered":"Questions about HMG wood splitter"},"content":{"rendered":"

When electrical problems the user should try a new cable and a new outlet to 90% supply is defective (extension cords or fuses at the house)! let Please check by an expert!<\/span><\/strong><\/p>\n

 <\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
problem<\/strong><\/td>\nreason<\/span><\/strong><\/td>\nmeasure<\/span><\/strong><\/td>\n<\/tr>\n
How do I find the product number and serial number?<\/span><\/span><\/td>\nThe device has an aluminum nameplate is riveted outside<\/span><\/td>\nType-specific data can be taken from the nameplate<\/span><\/td>\n<\/tr>\n
Extension cord 4 or 5<\/span> wire<\/span><\/span><\/td>\nExtension Cable extends with 4 wheels<\/span><\/td>\n5 cores need not be as 400V coil and no 230V is used<\/span><\/td>\n<\/tr>\n
My electric motor does not start or can not be turned on or makes strange noises<\/span><\/td>\nFor 95% of cases is always a broken supply line defective for machine<\/span><\/td>\nTry a new cable and connect it to another outlet<\/span><\/span><\/td>\n<\/tr>\n
Backup is turning off<\/span><\/td>\nHow many backups from falling? Falling 2 backups, then switch (semiconductor) defective.<\/span><\/td>\nReplace switch<\/span><\/td>\n<\/tr>\n
Green button does not stop<\/span><\/span><\/td>\n\n

 <\/p>\n

a. Wrong connection black wire<\/span><\/p>\n

b. Thermo contact faulty<\/p>\n

 <\/td>\n

\n

a. conductors replace the cable<\/span><\/p>\n

b. Switch exchange (bridging to test possible both on black!<\/span>)<\/span><\/td>\n<\/tr>\n

FI fuse<\/span> goes<\/span><\/span><\/td>\n\n

a. Moisture in the switch or motor<\/span><\/p>\n

b. Internal fault current<\/p>\n

c.<\/span> defective<\/span> line<\/span><\/p>\n

d. motor winding damage<\/span><\/p>\n

e. motor connected correctly<\/td>\n

checked by a qualified electrician<\/span><\/span><\/td>\n<\/tr>\n
Electric motor does not start or humming<\/span><\/span><\/td>\na. Wrong connection
\n<\/span>b. fall fuses
\n<\/span><\/p>\n

c. Motor protection responds<\/span>
\n<\/span><\/p>\n

d. Motor hums (400V Connection<\/span>)
\n<\/span><\/p>\n

e. Motor hums (230V Connection<\/span>) button (black or red<\/span>) outside of the switch box for Resat press (only 230 volt units)<\/span><\/td>\n

\n

a. checked lead by an expert<\/p>\n

b. Lead hedged too weak, possibly use larger fuses and stronger lead<\/p>\n

c. Lead to weak<\/p>\n

d. connected only 2 phases check supply<\/p>\n

e. key (black or red) button press outside of the switch box for Resat<\/td>\n<\/tr>\n

\n

Electric motor running in the wrong direction (400V Connection)<\/p>\n

 <\/td>\n

contact phase in the switch<\/td>\nTurn on the machine socket 2 pole plug with a screwdriver 180 (in front of the rotational movement the slot lightly press)<\/td>\n<\/tr>\n
Electric motor switches off suddenly during operation<\/td>\n\n

a. motor protection responds<\/p>\n

b. interrupted mains voltage<\/td>\n

\n

a. Allow the engine to cool, and check supply line, possibly missing a phase<\/p>\n

b. check the cables<\/td>\n<\/tr>\n

Switch does not work<\/td>\n\n

a. Wrong connection<\/p>\n

b. fall fuses<\/p>\n

c. motor hums<\/p>\n

d. Motor very hot<\/td>\n

\n

a. checked lead by an expertb. Lead hedged too weak, possibly use larger fuses and stronger lead<\/p>\n

c. connected only 2 phases, checked lead<\/p>\n

d. overload protection has triggered, let the motor cool down<\/td>\n<\/tr>\n

Splitting blade does not extend<\/td>\n\n

a. the motor rotation direction wrong<\/p>\n

b. Wrong direction of rotation of the PTO<\/p>\n

c. Not enough oil in the oil tank<\/p>\n

d. adjusted screw the adjustment linkage of the two-hand control<\/p>\n

e. Stroke splitting blade activated<\/td>\n

\n

a. Phase contact in the switch<\/p>\n

b. change direction of rotation<\/p>\n

c. Check the oil level<\/p>\n

d. must be set in the factory or by dealer<\/p>\n

e. Stroke solve splitting knife<\/td>\n<\/tr>\n

Splitting blade does not retract<\/td>\n\n

a. see Troubleshooting<\/p>\n

b. dissolved pin of the piston rod of the cylinder<\/p>\n

c. defective seals the cylinder<\/p>\n

d. Stroke splitting blade activated<\/td>\n

\n

a. “Splitting blade does not extendb. Mast with welded knife would go upstairs for pulling<\/p>\n

c. Seals the cylinder renew (Check cause, probably switched device in neutral position!)<\/p>\n

d. Stroke solve splitting knife<\/td>\n<\/tr>\n

Splitting blade does not force<\/td>\n\n

a. Not enough oil in the oil tank<\/p>\n

b. damaged cylinder seal kit<\/p>\n

c. worn hydraulic pump<\/p>\n

d. adjusted control valve or two-hand control<\/td>\n

\n

a. Check the oil level<\/p>\n

b. Dichtungssatz renew (Check cause, probably switched device in neutral position!)<\/p>\n

c. Replace the pump<\/p>\n

d. can be set in the factory or by dealer<\/td>\n<\/tr>\n

blocked splitting knife<\/td>\nWood too hasty<\/td>\nturn wood<\/td>\n<\/tr>\n
Splitting blade moves jerkily<\/td>\nNot enough oil in the oil tank<\/td>\nCheck the oil level<\/td>\n<\/tr>\n
Lowered cylinder moves not in working position (series HSP 10M-24M)<\/td>\nTwo-hand control is placed and fixed on NEUTRAL POSITION<\/td>\nLoosen travel stop after switching on the drive and slowly drive cylinder in the working position<\/td>\n<\/tr>\n
Drive dies shortly after takeoff from always (as tractor dies when switching the PTO from) (Series HSP 10M-24M)<\/td>\nCylinder is in transport position and two-hand control is not set to NEUTRAL POSITION<\/td>\nEnable Stroke while pressing a two-hand control<\/td>\n<\/tr>\n
Hydraulic lines are very hot<\/td>\n\n

a. Not enough oil in the oil tank<\/p>\n

b. PTO speed too high<\/p>\n

c. damaged hydraulic pump<\/td>\n

\n

a. Check the oil level<\/p>\n

b. comply with speed (the maximum speed is given another machine!)<\/p>\n

c. Replace the pump<\/td>\n<\/tr>\n

leaking hydraulic cylinders<\/td>\nworn sealing sleeve or piston rod<\/td>\nrenew<\/td>\n<\/tr>\n
no solution found<\/td>\ncontact workshop<\/td>\nTurn to retailer or HMG<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

<\/p>","protected":false},"excerpt":{"rendered":"

When electrical problems the user should try a new cable and a new outlet to […]<\/p>\n","protected":false},"author":4,"featured_media":0,"parent":529,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":[],"_links":{"self":[{"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/pages\/2394"}],"collection":[{"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/comments?post=2394"}],"version-history":[{"count":14,"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/pages\/2394\/revisions"}],"predecessor-version":[{"id":3128,"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/pages\/2394\/revisions\/3128"}],"up":[{"embeddable":true,"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/pages\/529"}],"wp:attachment":[{"href":"https:\/\/hmg-maschinen.de\/en\/wp-json\/wp\/v2\/media?parent=2394"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}